MARINE ENAMEL

 

QUICK DRYING - PAINT IN THE MORNING GO BOATING IN AFTERNOON

CAN BE BRUSHED ROLLED OR SPRAYED,

TURPS BASED   NO SPECIAL THINNERS NEEDED

 

INTERIOR AND EXTERIOR SURFACES  -  GLOSS FINISH    AND  QUICK  DRYING

 

CAN BE PAINTED ONTO MOST SOLID SURFACES, REMOVE ALL LOOSE PARTICLES, DUST AND OILS AND SAND OFF

 

TIMBER BARE SHOULD BE PRIMED

 

FIBERGLASS SHOULD BE SANDED BACK TO A SOLID SURFACE NO PRIMER REQUIRED

 

STEEL BARE SHOULD BE PRIMED WITH RED OR RED OXIDE PRIMER

 

ALUMINUM CAN BE APPLIED AFTER SANDING

 

AVAILABLE IN  1 AND  4

 

COVERAGE IS APPROXIMATELY 10-12 SQUARE METRES PER LITRE

 

CAN BE EASILY SANDED

 

RECOAT TIME 2 4 HOURS DEPENDING ON WEATHER CONDITIONS

 

IF YOU ARE NOT SURE ON THE SURFACE TRY A SMALL TEST PATCH FIRST  

AVAILABLE IN  WHITE, BLACK, BLUE, DEEP BLUE, ISLAND BLUE , RED, REEF BLUE,

 SAFETY YELLOW , WHITE  AND MANY PASTEL COLOURS

 

COLOURS LEFT TO RIGHT

BLUE, LIGHT GREY,  GREEN,  BLACK, YELLOW, RED, SAFETY YELLOW,

  

  



MARINE RED & GREY OXIDE PHOSPHATED PRIMER


SPECIALLY FORMULATED WITH ANTI CORROSIVE PROPERTIES FOR PREVENTING RUST ON BARE STEEL. NOT TO BE USED ON ALUMINIUM OR GALVANISED SURFACES UNLESS SURFACE IS BROCKEN.

STEEL MUST BE CLEANED, FREE FROM OILS, AND ALL SURFACE RUST REMOVED BEFORE APPLICATION.

THIS PRODUCT CAN STOP RUST ON ITS OWN BUT TOP COATING IS RECOMENDED

YOU CAN BRUSH, ROLL, OR SPRAY.

IF SPRAYING, THINNING WITH TURPS MAY BE NECESSARY DEPENDING ON SPRAY EQUIPMENT, NOZZE SIZE, AND POWER OF SPRAY UNIT. ONLY THIN ENOUGH TO GET THROUGH SPRAY GUN.

WASHES UP IN MINERAL TURPS. DO USE THINNERS OR OTHER SOLVENTS.

DRYING TIME IS 2-6 HOURS DEPENDING ON WEATHER CONDITIONS.

COVERAGE IS 6-12 SQUARE METRES PER LITRE DEPENDING ON SURFACE AND APPLICATION METHOD

MINERAL SOLVENT BASED TOP COATS ARE RECOMMENDED.

DOES NOT CONTAIN ANY LEAD OR MERCURY BASED PRODUCTS.

AVAILABLE IN 1 AND 4 LITRE CANS






 

MARINE PLYWOOD

 & TIMBER SEALER

SPECIALLY  FORMULATED FOR MARINE STANDARD APPLICATIONS.

EXCELLENT GLOSS HOLD OUT, SANDE EASILY, HIGH FILLING

SURFACE MUST BE CLEAN,  FREE  FROM OILS, AND ALL LOOSE PARTICLES REMOVED BEFORE APPLICATION.

 

APPLICATION BY BRUSH,  ROLLER, OR SPRAY.

 

IF SPRAYING, THINNING WITH TURPS MAY BE NECESSARY.

 

WASHES UP IN MINERAL TURPS

 

DRYING TIME IS 4-6 HOURS DEPENDING ON WEATHER CONDITIONS.

 

COVERAGE IS 6-12 SQUARE METRES PER LITRE.

 

CAN BE OVER COATED WITH WATER BASED OR SOLVENT BASED TOP COATS

 

DOES NOT CONTAIN  ANY LEAD OR MERCURY BASED PRODUCTS.

 

AVAILABLE IN 1 AND 4 LITRE CANS

 




MARINE CLEAR

MARINE CLEAR IS A SINGLE PACK POLYURETHANE FINISH FOR TIMBER, FIBREGLASS, PRIMED METAL, AND PLYWOODS.

YOU CAN USE THIS PRODUCT STRAIGHT OUT OF THE TIN WITH NO SEALERS REQUIRED.

IT IS STRONG ENOUGH TO BE USED ON FLOORS, BENCH TOPS, SHELVING, AND TRIM WORK.

DRIES TO A HARD DURABLE GLOSS FINISH

COVERAGE ON BARE SURFACES 5 10 SQUARE METRES PER LITRE


COVERAGE ON COATED SURFACES 10 14 SQUARE METRES PER LITRE

DRYING AND RECOAT TIME IS 1 TO 3 HOURS


CAN BE BRUSHED, ROLLED, LAMBSWOOL APPLICATOR, SPRAYED

INTERIOR SURFACES ONLY


DO NOT ADD ANY OTHER THINNERS OR SOLVENTS AS THIS MAY CAUSE A DETERIATION IN THE QUALITY

THINNING AND WASHING JUST USE MINERAL TURPS


AVAILABLE IN 1, AND 4 LITRE CANS