INDUSTRIAL COATINGS

 

 

GREY & RED OXIDE ZINC CHROMATE PRIMER

SPECIALLY FORMULATED WITH ANTI CORROSIVE PROPERTIES FOR PREVENTING RUST ON BARE STEEL.

STEEL MUST BE CLEANED, FREE FROM OILS, AND ALL SURFACE RUST REMOVED BEFORE APPLICATION.

APPLICATION BY BRUSH, ROLLER, OR SPRAY.

IF SPRAYING, THINNING WITH TURPS MAY BE NECESSARY.

WASHES UP IN MINERAL TURPS

DRYING TIME IS 2-6 HOURS DEPENDING ON WEATHER CONDITIONS.

COVERAGE IS 6-12 SQUARE METRES PER LITRE.

MINERAL SOLVENT BASED TOP COATS ARE RECOMMENDED.

DOES NOT CONTAIN ANY LEAD OR MERCURY BASED PRODUCTS.

AVAILABLE IN 500ML 1 AND 4 LITRE CANS


 

  




 

ONE COAT SILVERCOAT

CAN BE BRUSHED, ROLLED OR SPRAYED

RECOAT TIME IS 6 TO 24 HOURS DEPENDING ON CONDITIONS

INTERIOR AND EXTERIOR APPLICATION

PREPARATION

BARE STEEL SHOULD BE UNDERCOATED WITH CRYSTAL RED OR GREY OXIDE PRIMER

GALVANIZED SURFACES SHOULD BE FREE FROM ALL DUST, LOOSE PARTICLES, OXIDIZATION , OILS AND MOISTURE

MAY BE USED ON APPROPRIATELY PREPARED TIMBER AND WOOD

CANNOT BE TINTED

IF THINNING USE ONLY MINERAL TURPS, DO NOT MIX WITH OTHER PAINTS

COVERAGE IS 10-16 SQUARE METRES PER LITRE

WASHES UP IN MINERAL TURPS


 

 

 




AUTOMOTIVE PAINT

          
This is a polyurethane based enamel that is very easy to use for basic automotive,
truck, motorcycle, and machinery jobs.
 Can be brushed, rolled or sprayed.
 Re coat time is 2 4 hours depending on weather conditions.
 Thinning and clean up use mineral turps only.

PREPARATION
 Can be painted onto most solid pre painted surfaces. Remove all oxidation, oils
etc. then key sand off and do a small test patch first on the prepared surface to
compare compatibility.
 Bare steel should be undercoated with crystal red or grey oxide zinc chromate
primer.
 Motorcycle plastic fairings can be sanded lightly and applied straight on.
 Automotive plastics and fiberglass can be applied straight on after a fine sand.
 Colours available white, blue, black, yellow, golden yellow, red and many lighter
colours.
 Do not mix with any other paints, solvents or additives as this could effect the
performance of the paint.
 Coverage is 10-12 square metres per litre.

WHAT ELSE DO I NEED TO KNOW?
1. If you're going to spray, you will need to thin the paint out about 5-10%
mineral turps or more depending on your spray unit.
2. Do not paint if the temperature is less then 12 degrees C.

AVAILABLE IN 1 AND 4 LITRE CANS



  


   



 


 



 

 

PAVING PAINT COLORS

TOUGH POLYURETHANE SEMI GLOSS FINISH

REPELS WATER AND OILS

SUITABLE FOR CONCRETE AND TIMBER SURFACES SUCH AS PATHWAYS, DRIVEWAYS, SHOWROOMS, PATIOS, WORKSHOPS, ECT.

APPLICATION BY BRUSH OR ROLLER, IF SPRAYING FOLLOW WITH ROLLER

YOU CAN RECOAT AND WALK ON AFTER 30 MINUTES TO 3 HOURS DEPENDING ON CONDITIONS

NEW CONCRETE SHOULD WEATHERED FOR 2-3 MONTHS BEFORE PAINTING

CONCRETE SHOULD BE ACID ETCHED AND HIGH PRESSURE CLEANED

BARE TIMBER WILL REQUIRE PRIMING OR UNDERCOATING

COVERAGE IS 8 TO 15 SQUARE METRES PER LITRE

WASHES UP IN MINERAL TURPS

FOR STEEP AND VERY SMOOTH SURFACES FINE SAND SHOULD BE SPRINKLED ON BETWEEN COATS

COLOURS - BEIGE TAN, BLACK, BLUE, DEEP GREEN, FERRIC RED, GREEN, LIGHT GREY, LIGHT OCHRE,

MID GREY, SAFETY YELLOW, SANDSTONE, SIENNA, TERRACOOTA, YELLOW,

ALSO AVAILABLE IN WHITE THAT CAN BE TINTED TO PASTEL COLORS

AVAILABLE IN 1 , 4 , 10 LITRE CANS


 






QUICK DRYING BRUSHING ENAMEL

CAN BE BRUSHED, ROLLED OR SPRAYED

RECOAT TIME IS 1 TO 3 HOURS DEPENDING ON CONDITIONS

INTERIOR AND EXTERIOR

PREPERATION

BARE STEEL SHOULD BE UNDERCOATED WITH CRYSTAL RED OR GREY OXIDE PRIMER

TIMBER SHOULD BE UNDERCOATED WITH CRYSTAL ACRYLIC SEALER UNDERCOAT,

 ACRYLIC MULTI PURPOSE PRIMER OR ALL PURPOSE UNDERCOAT

GALVANISED SURFACES SHOULD BE UNDERCOATED WITH CRYSTAL GALVANISED IRON PRIMER.

WHITE, BLACK, GREY , RED, YELLOW, SAFETY YELLOW, GREEN,

CAN BE TINTED LIKE NORMAL WHITE PAINT

COVERAGE IS 10-15 SQUARE METRES PER LITRE

WASHES UP IN MINERAL TURPS

AVAILABLE IN 1, 4 and 10 LITRE CANS